Get the SM-76A User Manual as a PDF
We'll email you a printable copy.
1. Safety Information
Please read this manual carefully before using your SM‑76A and always follow the operating steps below.
- •Make sure your power supply matches the machine rating (110–220 V AC) before switching on.
- •Warning: the outlet must be properly grounded. An ungrounded supply can cause serious injury or damage the machine.
- •Use the machine indoors only. Never place it outdoors or wash it down with water.
- •Never use the machine barefoot — always wear shoes.
- •Do not step on the footboard while film is feeding.
- •Do not put any foreign objects into the machine.
- •Children must not use or play with the machine unsupervised.
- •Do not use the machine on floors with water or oil — take care to avoid slipping.
- •Always unplug the machine before maintenance, cleaning or moving it.
- •Keep the ventilation slot on the bottom of the machine clear so it can operate normally.
- •Only use genuine SoleMate SM‑76A film rolls.
2. Operating Conditions
- •Use in a clean, dry indoor environment that is free of heavy conductive fibers or dust.
- •Room temperature: 41–104 °F (5–40 °C). Relative humidity: 87% or less.
- •Elevation: below 3,280 ft (1,000 m).
- •The film naturally carries a small static charge. If your area has static‑control (ESD) requirements, confirm the machine is suitable for that space before use.
3. Product Overview
The SoleMate SM‑76A is a hands‑free, high‑capacity automatic shoe cover machine. Step onto the footboard and a thermo‑shrink film cover is shaped around your shoe in seconds, while the handle bar keeps you steady.
Key Features
- ✓High capacity: 1,600 pieces (800 pairs) per roll — fewer roll changes
- ✓Handle bar for stability and balance during use
- ✓LCD control panel with adjustable heat, film counter, clock and automatic working hours
- ✓“Warm Wind” mode for warming or drying
- ✓Fits US Men's sizes 5–14 (Women's up to approx. 16)
Main Components
- •Top cover with LCD screen and four function keys
- •Footboard (marked “PRESS”)
- •Rear cover and film compartment
- •Film outlet
- •Detachable handle bar (Handrail A and Handrail B) and bottom case
- •Rear wheels
- •Power socket
- •Ventilation slot (underside)
4. Installation & Setup
4.1 What's in the box
- •SoleMate SM‑76A shoe cover machine — 1
- •User manual — 1
- •Power cord — 1
- •Film roll — 1
- •Detachable handle bar set (Handrail A, Handrail B and bottom case) — 1
- •M6 hex (Allen) wrench — 1
- •M6 hex bolts — 4
If anything is missing or damaged, do not use the machine — contact SoleMate.
4.2 Assemble the handle bar and base
- 1Insert Handrail B into the slot on the bottom case.
- 2Fit the four M6 hex bolts and tighten them with the M6 hex wrench.
- 3Insert Handrail A into Handrail B and press it firmly into place.
- 4Set the machine’s rear wheels into the two half‑slots on the bottom case.
4.3 Placement
- •Place the machine on a flat, stable, dry floor, away from doorways or strong drafts.
- •Allow clear space for users to step on and off safely.
- •Keep the underside ventilation slot unobstructed.
4.4 Power connection
- 1Plug the power cord into the machine’s socket, then into a grounded wall outlet.
- 2Press the power (Enter) key to switch the machine on.
- 3Allow about 3 minutes for the heater to warm up before first use.
5. Loading and Replacing the Film Roll
Use only genuine SoleMate SM‑76A film (SM‑1000‑BB‑PETG or SM‑1000‑BB). SM‑76C film does not fit this machine.
- 1Open the rear cover of the machine.
- 2Trim or clean any burrs or rough edges from the start of the film so the leading edge is smooth.
- 3Place the film roll horizontally into the film compartment.
- 4With one hand, guide the film end into the middle of the film outlet.
- 5At the same time, press the Up (▲) key with your other hand to draw the film into the machine until it stops in position.
- 6Press the footboard down by hand and release — the film is automatically fed out to the working position.
- 7Close the rear cover.
Film won't catch? Press the Down (▼) key to back the film out, then repeat steps 4–6.
New roll loaded? Update the film counter — see “Reset Remain” in section 8.
6. Normal Operation
6.1 Applying shoe covers
- 1Make sure the film is in the working position and the machine has warmed up.
- 2Hold the handle bar and step onto the area marked “PRESS”.
- 3Hold still. When the screen digits light up and you hear a long beep, the cover is shaped (about 2–5 seconds).
- 4Lift your foot off the footboard — the next film is fed out automatically.
- 5Repeat with your other foot.
6.2 Turning off
Press the power (Enter) key to switch the machine off. Unplug it if it will not be used for a long period.
6.3 Best practices
- ✓Step straight on and straight off; don’t twist your foot during shaping.
- ✓Walk normally after application; don’t run or drag your feet.
- ✓If a cover looks loose or incomplete, remove it and apply a new one.
7. Control Panel
The control panel has an LCD screen and four function keys:
| Up (▲) | Feeds film into the machine; increases a setting value |
| Down (▼) | Backs film out of the machine; decreases a setting value |
| Next | Moves to the next function or value |
| Enter | Turns the machine on/off; saves a setting and returns |
Press Next to cycle through the three main functions:
- •Shoe Covering — the default working mode.
- •Warm Wind — runs the heater continuously to warm or dry. Make sure there is no film on the footboard, then press the footboard to start. Use ▲ / ▼ to raise or lower the heat level (default: 3). Press Enter to exit (the machine turns off) or Next to return to Shoe Covering.
- •Data Adjustment — the settings menu (see section 8).
Shoe Covering
Default mode. ▲ / ▼ feed film in or out, Enter turns the machine on or off.
Warm Wind
▲ / ▼ change heat level (default 3). Next returns to Shoe Covering, Enter exits.
Data Adjustment
Press Next until “Adjust” shows, then Enter to open the settings.
Example screens with default values. Highlighted keys are the ones you use on that screen.
8. Settings (Data Adjustment)
Press Next until “Adjust” is shown, then press Enter. Press Next to move between the five settings, and Enter to save and go back.
| Reset Remain | Sets the film counter to match the count on the roll (or your estimate of what is left). ▲ / ▼ change it in steps of 100. |
| Temp. Control | Shaping heat level, 1–9 (default 2). Fine‑tune to your preference — raise one level if covers are loose. |
| Reset Time | Sets the clock. Press Enter or Next to show the cursor, Next to move between digits, ▲ / ▼ to change them. |
| Working Time | Sets automatic daily on/off hours (default 08:10–18:15). Edit the same way as the clock. |
| Cancel Timing | Turns off the automatic working‑hours schedule. Press Enter to save. |
Reset Remain
▲ / ▼ change the film count in steps of 100. Enter saves.
Temp. Control
Heat level 1–9 (default 2). Enter saves.
Reset Time
Next moves the cursor, ▲ / ▼ change the digit. Enter saves.
Working Time
Daily on/off hours (default 08:10–18:15). Enter saves.
Cancel Timing
Turns the working-hours schedule off. Enter saves.
Example screens with default values. Highlighted keys are the ones you use on that screen.
9. Cleaning and Maintenance
Always turn OFF and unplug the machine before cleaning or maintenance.
- •Wipe the exterior with a soft cloth lightly dampened with mild detergent or disinfectant.
- •Never wash the machine with water or pour liquids onto it or into its openings.
- •Regularly clear dust and film scraps from the ventilation slot on the underside.
- •Periodically inspect the power cord and plug for damage.
- •For any internal repair, contact SoleMate support.
10. Storage and Transport
- •Turn the machine OFF and unplug it before moving or storing.
- •Use the rear wheels to roll the machine short distances; lift it off the base — do not drag or drop it.
- •For long‑term storage, remove the film roll and keep it in a cool, dry place, and cover the machine to protect it from dust.
11. Technical Specifications
| Model | SoleMate SM‑76A High‑Capacity Automatic Shoe Cover Machine |
| Dimensions (L × W × H) | 30.6 × 17.5 × 15.0 in (778 × 445 × 382 mm) |
| Ground clearance | 0.8 in (20 mm) |
| Net weight | Approx. 40 lbs (18 kg) |
| Power | 110–220 V AC, 50/60 Hz (grounded outlet required) |
| Maximum power | 1,300 W |
| Standby power (heater warm) | 75 W |
| Warm‑up time at start | Approx. 3 minutes |
| Film‑feeding time | Approx. 3.5 seconds |
| Cover shaping time | 2–5 seconds per foot |
| Maximum heater temperature | 482 °F (250 °C) |
| Shoe size fit | US Men's 5–14 (Women's up to approx. 16) |
| Film | SoleMate SM‑76A high‑capacity film only — PETG (SM‑1000‑BB‑PETG, recommended) or PVC (SM‑1000‑BB) |
| Capacity | 1,600 pieces (800 pairs) per roll; 2 rolls per film box = 1,600 pairs |
| Operating environment | Indoor, clean and dry; 41–104 °F (5–40 °C); humidity ≤ 87%; elevation below 3,280 ft (1,000 m) |
| Warranty | SoleMate 12‑month limited warranty |